How do you hook up an amp


www.cantinesanpancrazio.it/components/tykewozi/1210-configurare-dati-cellulare.php Make sure you always turn off your amp when you leave your car, it will overheat and drain your battery. Turn the gain all the way down, start playing music and turn it up to where you usually listen, where the mids sound good. Tune them gain until the subs sound good.

Already answered Not a question Bad question Other. Tips Don't forget to test your rem wire before you assume it works. Gather your equipment Amp, Subs, Stereo, and wiring. Then run the remote wire back to the amp and cut it there leaving a foot or so of extra cable. Since you'll have to run cables and wires between the subwoofer and other devices, you might want to keep it just a few feet from your screen.

RMS is very important when matching subs and amps, yes not enough power will make subs clip, but also to much power will burn your voice coils by over heating them with too much power. Subs and amps should be matched as closely as possible for best performance and longevity.

Video of the Day

I have a Pioneer deck, amp, and kicker, installed to shut off from the battery. The sub cuts on and off at high volume when I use the auxiliary cord to phone. How do I fix this? That could mean your amp cannot handle the sub. Another important factor to consider is Ohms.

If you have a 2 ohm sub and a 4 ohm amp it won't produce enough power to properly power the sub. Not Helpful 2 Helpful The wires are not grounded properly, check to make sure the surface is clean, unpainted metal.

How to Hook Up a Car Amp Inside the House to a Wall Outlet

Not Helpful 6 Helpful Not Helpful 5 Helpful What would cause my sub to kick in when radio is on and stop working when I change source to CD? The remote antenna power wire is responsible for the antenna coming out of a car with a retractable antenna. Remove the wire and find the correct remote amp, then turn on wire or ignition wire to the vehicle. Not Helpful 15 Helpful You should be able to connect it to the auxiliary on the back of the stereo unit.

Not Helpful 3 Helpful 7. My amp is already installed and I just bought a new sub. How do I connect my new sub to my old amp? There should be RCA female plugs on your amp, and on the new sub-box enclosure, there should be another set of RCA plugs or clamps. Just match the positive and negatives.

  • .
  • best dating place in ncr.
  • how do you know youre dating the wrong person?
  • .
  • .
  • ;
  • best dating sims for guys android;

Not Helpful 14 Helpful Remote; connect the REM wire to a fuse that only has power when the car is on. I cannot turn it up any higher than halfway without my amp going into protective mode. What would cause this? This could be caused by a bad ground. Run yourself a good wire for ground directly to the chassis. Not Helpful 1 Helpful 3. What if I bought my radio harness to fit my truck only? Will the wires still match up on the aftermarket radio I purchased?

How To Hook Up Car Audio Amplifier For Subs - Basic and Simple Guide

It will just plug into your truck and then connect color coordinated wires. Not Helpful 0 Helpful 1. How should I connect the remote wire so that I don't have to disconnect it when I turn off the car? Hook it to a fuse connected to ignition turn on, like your accessory power fuse. Not Helpful 16 Helpful What do I do if my amp comes on with static through my speakers when I turn on the key, but nothing else comes through?

Answer this question Flag as Where do you get lock nuts for the power and ground wires on my amp? Can I run 4 speakers and a subwoofer from a single amplifier? Can I hook up a loc to the rear speaker wires if there is a factory amp to them?

How do you connect a subwoofer to an amplifier?

If not, where do I hook up the loc wires? Can you add subs to a factory radio?

If so short simple easy way? And how can you test your subs to see if there working. Include your email address to get a message when this question is answered. Already answered Not a question Bad question Other. Tips Don't forget to test your rem wire before you assume it works. Last thing you need is a dead battery. If your amp doesn't turn on, check the amp fuses. Wall outlets provide volt AC power, but amplifiers require volt DC power. You'll have to do a little extra wiring, but the problem is not insurmountable.

Next its time to hook up the speaker wire from the sub to amp. In this case the wires are blue. The blue wire with the white stripe is positive and the solid blue is . The remote wire will "tell" your amplifier to turn on whenever the stereo is powered up (usually, whenever the vehicle is turned on). You'll have to remove the.

Look up the input power specifications for your amplifier, using the manual or the manufacturer's website. Find the specification for current draw in amperes.

How to Wire an Amp to a Sub and Head Unit: 12 Steps

Purchase an AC to DC power inverter. Make sure the inverter can produce a volt DC output at the specified amperage rating. Cut a length of gauge red wire, a length of gauge black wire and a length of gauge wire, each long enough to reach from the amplifier to the inverter. Loosen the REM terminal of the amplifier with a screwdriver. Slide the ends of your wires into the loosened terminals and tighten down to clamp the wires.